A Comprehensive Analysis of Bezel Setting

Loose Cushion Cut Diamond

Bezel Setting Tips

The bezel setting is one of the most popular ways to mount gemstones over rings or other types of jewelry. This setting covers the entire gemstone using a strip of metal. It is considered a safe setting for diamonds. Below is a discussion on its pros and cons as well as its comparison with other prominent settings.

Pros And Cons Of Bezel Settings


Well Guarded Diamonds

Bezel settings offer more protection to diamonds than many other settings. This is because the metal completely covers the diamond. The gemstone stays protected from wear and tear.

Internally Flawless Appearance

Internally Flawless is a term used to refer to diamonds which are completely free from imperfections. These diamonds are highly expensive. When you set your diamond in a bezel setting, it covers all the edges of the diamond. This conceals any inclusion present in the diamond and makes it appear clean.


Waste Of Sparkling Stones

In a bezel setting, diamonds are covered on all sides by metals as mentioned above. This prevents light from entering it from all sides. Therefore, the gemstone does not get to display the full range of sparkle that it is capable of.


Bezel settings are made from a lot of hard work. Therefore, they also cost higher than many other setting and are considered expensive by many.

Full Vs. Partial Bezel Settings

Full bezel settings complete an entire circle around the gemstone while partial bezel setting surrounds the diamond only partially. The benefit of the partial setting is that they do not cover the diamond as much as a full bezel setting does. Diamonds appear attractive in a partial bezel setting as the light now enters the diamonds through the gap. This way it is able to sparkle and display its brilliance to a certain extent. Apart from this, partial bezel settings allow you to clean the diamonds in a better way. At the same time, they have a disadvantage that they leave a part of the diamond exposed. This may cause them to chip or pick up damages.

Bezel Settings Vs. Prong Settings

Prong settings have an upper hand over the bezel setting that they are cheaper than the latter. If you are looking for a budget-friendly purchase, you can go with the prong setting. Besides, the prong setting emphasizes the brilliance of the diamond because it allows a large portion of the diamond to be exposed. Light will be able to enter the diamond and it shines with all its brilliance, unlike loose cushion cut diamond.

A prong setting is always the better option if you ever want to switch the diamonds in the future. However, this is not possible in a bezel setting as it is permanent once it is made.

The prong setting has a downside that they are more exposed to impacts from outside. On the other hand, bezel settings offer protection to the rings. As a result, diamonds in prong setting require maintenance from time to time.

In the case of the prong setting breaks, the gemstone might be lost forever. Due to this, prongs have to be changed after a certain number of years. Bezel settings hold their structure for a much longer period.

When To Choose A Bezel Setting

Bezel settings are the best option for people who use their hands while working every day. If they are involved in a job that has a high probability of hitting somewhere, bezel setting will offer the basic protection to the diamond inside. Besides, it is also good at hiding the flaws. In case the gemstone you choose has a hardness value of less than 6 or 7 on the Mohs hardness scale, the bezel setting is the way to go. For instance, choose bezel setting if you have a turquoise or opal gemstone

Inspecting Bezels

The bezel setting is an important component of the rings where it is used. Therefore, it is important that you inspect them carefully before purchasing to ensure quality. Below are a few features that you have to look for while purchasing them:

  • A secure and tight fit that holds the stone firmly in place. There shall be no loose sides or gaps.
  • The stone should be at the same level as the principal facets and should be aligned with the symmetrical design that the ring is made of. For instance, this should be along the edges or the band of the bezel.
  • The rim should have an even profile without any sharp protrusions.
  • The rim should not have any damages on them or at the point where the metal and the rim meet.

Bezel settings involve a higher level of difficulty in its manufacturing phases. Therefore, it is costlier than in other settings. However, they offer several advantages like safety and security to the gemstone they carry such as loose emerald cut diamond. Make sure you keep the above points in mind before heading out to purchase them.